Don't see what you need? Fill out more generic Request For Quote Form
Picklewood Siding is processed from recycled pickling vats. The material reclaimed from pickle vats had been in service for up to 100 years prior to being salvaged and as a result has a rustic weathered patina. Picklewood Species often available include Redwood, Cypress, Douglas Fir and White Cedar. Available Configurations: Board-and-Bat, Board-on-Board, Board-to-Board, and Shiplap.
|Species||Various - can include Cypress, Redwood, Douglas Fir, Cedar, and/or other.|
|Source||Pickle Vats salvaged from different sites in North America|
|Holes||Occasional nail holes, especially on the ends; no visible bolt holes (boards were sometimes assembled with wood dowels so there are some dowel holes on the edge which are split through on the sawn face of Picklewood Weathered Split)|
|Knots||90% clear. Some boards will have pin knots.|
|Checking/Cracks||Unlimited as long as board is sound; end cracks to extend no more than 6" into board; many boards have dark checking|
|Grain Pattern||Tight grain; Mixed|
|Standard Dimensions||a) Thickness: As-is boards range from 1 1/2" to 2 1/2" thick. Split boards will be approx. 5/8" (boards will be split from thicker as-is boards; some thickness variation is to be expected due to (1) inexact splitting and (2) slight differences in thickness of as-is boards); b) Width (nominal): 3"-7". Widths will be camp-run and will tend to be grouped heavily around 5"; and c) Length: generally up to 7'6", with many pieces 6' to 7'6" (longer pieces may beavailable if specifically requested and quoted.) See next item about dimension counts.|
|Dimension Counts||As-is material thickness will be tallied to the original 1/2" (material which was originally cut at 1 1/2" may have weathered to slightly under 1 1/2" thick). The thickness of the split material is approximately 5/8" thick, but is tallied as if it were 4/4". The width will be tallied to the closest inch (6.5" tallied as 7"; 6.375" tallied as 6".) The length will be measured in half-foot increments. Where the length does not reach a specific half-foot increment, the piece will be tallied at the next lower half-foot (a piece 7'9" will be tallied as 7.5'; a piece 6'5" will be tallied as 6'.)|
|Weight||Typically, approximately 3 pounds per board foot|
|Surfacing||As-is material is weathered on all four sides. Split material is Weathered on one face (reverse face is bandsawn).|
|Salt/Minerals||Picklewood materials contain significant amounts of salt and other minerals, creating special characteristics and/or considerations like those described in the following items.|
|Color/Appearance||The coloring of individual Picklewood boards varies widely. Weathered faces can include a range of grays and browns (the exterior of the pickle vats generally weathered to grays, while the interior generally weathered to browns.) Processed Picklewood materials have color variations which range from normal Douglas Fir coloring to color combinations unique to Picklewood materials.|
|Finishes/Glues||Certain finishes and glues do not work well with Picklewood materials. Most importantly, DO NOT USE WATER-BASED FINISHES.|
|Metal Corrosiveness||Picklewood materials can have a corrosive effect on metal fasteners, machinery and saw blades. Stainless steel fasteners should be used in lieu of regular steel fasteners, especially in applications involving the likely mixing of Picklewood, moisture and oxygen.|
|Moisture||Picklewood absorbs moisture more readily than typical Douglas Fir. Picklewood material (especially material with air dry or kiln dry time) should be handled, stored and transported carefully to minimize any unnecessary reabsorption of moisture.|
|Odor||Picklewood materials often have a strong pickling smell to them. This odor is especially strong as wet material is|
being cut or otherwise processed. It tends to become less and less of an issue as material is allowed to air dry (or as material is kiln dried).
|Salt Leaching||As moisture is drawn out of Picklewood materials, it brings salt with it. Salt leaching tends to be the most concentrated at knots and material ends, but can happen anywhere. Air dry time (and kiln drying) reduces, but does not eliminate, salt leaching. Approaches to salt leaching include sanding and refinishing impacted areas to doing nothing (and letting the salt serve as one of the most visible evidences of the history and reclaimed nature of Picklewood materials.) Salt is more visible on processed materials than on as-is materials.|
|Appearance Variation||Boards can vary in appearance from piece to piece and even within a piece. The characteristics described on this specification sheet generally apply to each board's featured face. The opposite face and edges can differ from the featured face in texture, coloring, and other characteristics unless otherwise noted. Weathered lumber / barnwood will have at least one weathered face. The opposite face and edges can be any combination of weathered and fresh-sawn. If weathered, the weathering will often be different (amount, mix of colors, etc) than on the featured face.|
Trestlewood sometimes uses one or more juicing processes to help fresh-sawn and/or less weathered/aged faces/edges blend in with weathered faces/edges. All else being equal, juicing is more likely to be used in situations where (a) lumber is cut from timbers or wider lumber (thereby creating fresh-cut faces and/or edges); (b) Buyer wants all (or most) faces/edges to be weathered/aged; (c) Buyer desires to increase the consistency of the weathered/aged look from face to face; and/or (d) Buyer wants a darker weathered look.