Shop Standard Configurations(great value and good lead times!)
|Antique Barnwood Gray Rough Lumber|
|1"||Rand 4-8"||Rand 4-12'||$6.50|
$5.85 per bf
|Antique Barnwood Gray Rough Lumber|
Request Custom Quote(additional costs and lead times generally apply)
|Antique Barnwood Gray Rough Lumber|
specific height, width and length
1 to 3"
Don't see what you need? Fill out our more generic Request for Quote form.
Antique Barnwood - Gray - Product Info
Trestlewood's Antique Barnwood is carefully reclaimed from siding, roof boards, granary boards, loft floors and other parts of vintage structures. Antique Barnwood is regularly used for exterior siding, interior paneling, ceiling material, soffit material, fascia, base and case, trim, doors, cabinets, etc.
We sort our Antique Barnwood into three general buckets: Gray Rough, Brown Rough and Smooth Brown/Gray (heavier to browns). You are, of course, welcome to mix and match any of these colors/textures for your particular application.
Are you wanting that Antique Barnwood "look" but at a more aggressive price point? Be sure to check out our NatureAged Barnwood and WeatheredBlend Barnwood for products designed to give you the best value for your dollar!
|Species||Mixed Species. May include Pines, Firs, Spruce, Larch, Oak, Elm, Hickory, Hemlock, Ash, Maple, Beech, Poplar, Cedar, Redwood, Cypress, and/or other species. Generally heavy to (or even exclusively) softwoods unless hardwoods are specifically ordered. Trestlewood can include hardwoods at its discretion. Trestlewood generally does not sort its weathered lumber products by species (its focus is on look, not species) and is, therefore, generally not in a position to provide weathered lumber in a specific species. Mixed Species means that any combination of species (including all one species) is allowed.|
|Source||Barns, corncribs, stables, mills, fences, homes, and other buildings and agricultural/industrial/construction structures and materials from different locations in North America; can include lumber which is resawn from reclaimed timber/poles/lumber and then laid out to weather.|
|Metal/Holes||Nails, fasteners, and other metal can be removed or left in at Trestlewood's discretion (Trestlewood is especially likely to leave metal whose removal could be expected to result in the gouging of barnwood faces/edges); where left in, metal will often be cut flush, broken off or pushed in to facilitate efficient stacking/handling. Metal removal / metal detection is sometimes available at an additional charge. Antique Barnwood will generally have some nail holes and can have an occasional bolt hole. Staining around holes/metal is common.|
|Knots||Unlimited knots; some tight, some loose or fallen out|
|Checking/Cracks||Unlimited as long as board is sound|
|Moisture Content/Stability||Air-Dried. Moisture content and stability of a specific board depend on a variety of factors, including source, season of year, weather, location stored, etc. Barnwood lumber is typically stored outside and can get quite wet during the winter and other periods of wet weather. Kiln drying is generally available at an additional charge. Antique Barnwood is generally more stable and less prone to shrinkage and other movement than is green lumber. Wood is wood and will move.|
|Standard Dimensions||a) Thickness: 1" (actual: 5/8" to 4/4") and 2" (actual: 1 1/2" to 8/4"); b) Width: random, 4" to 8"; 10" and 12" widths are also often available (actual widths can be as much as 3/4" nominal); c) Lengths: 3' to 12'. |
Where more consistent thicknesses and/or widths are desired, thickness planing/resawing and/or edging processing options are often available. Boards can have small sections that fall outside standard thickness and/or width ranges. Trestlewood will often leave board ends that dip below 5/8" thick (or otherwise fall outside standard dimension ranges) to give the Buyer as much flexibility as possible, but exclude those ends when tallying board footage so as to not charge the Buyer for ends that will likely need to be trimmed in the field.
|Weight||Depends on species mix and other factors. Typically, 2.5-3.0 pounds per board foot.|
|Surfacing/Texture/Colors||Weathered; Trestlewood sorts Antique Barnwood Lumber into Rough Gray Barnwood, Rough Brown Barnwood, and Smooth Brown/Gray Barnwood (generally heavy to browns.) One of the unique features of Antique Barnwood is the range of textures found therein. The surfacing and texture of different barnwood sources may vary widely. Antique Barnwood Lumber colors vary as well - common colors include browns, light browns, grays, light grays and combinations of browns and grays. Many boards will have multiple shades of colors. Some boards may have striping as a result of variations in weathering from being attached to other material during use. As a result, Trestlewood generally does not offer a color sort which does not allow for some latitude in the colors provided. Brown barn boards often include some gray tones; gray barn boards often include some brown tones.|
|Appearance Variation||Boards can vary in appearance from piece to piece and even within a piece. The characteristics described on this specification sheet generally apply to each board's featured face. The opposite face and edges can differ from the featured face in texture, coloring, and other characteristics unless otherwise noted. Weathered lumber / barnwood will have at least one weathered face. The opposite face and edges can be any combination of weathered and fresh-sawn. If weathered, the weathering will often be different (amount, mix of colors, etc) than on the featured face.|
|Siding Product Configurations||When Trestlewood quotes 1,000 square feet of a specific siding configuration, it is quoting enough material to provide 1,000 square feet of coverage based on default installation assumptions and 0% installation falldown. Buyer should order enough product to cover anticipated installation falldown and the impact of any changes to installation assumptions. Siding configuration options include:|
(a) Board to Board (common widths: 4", 6", 8", 10", mixed)
(b) Board and Batten (common board widths: 8", 10", 12"; typical batten width: 4"; assumed: installed with 2" gaps between boards)
(c) Board on Board (common widths: 6", 8", 10", mixed; assumed: installed with 1" overlap on each edge)
(d) Shiplap (common face widths: 5", 7", 9" (often actual face widths of 4 7/8", 6 7/8", 8 3/4"); target thickness often 3/4"+/- for NatureAged and 11/16"+/- for Antique and WeatheredBlend; most commonly, 3/8" shiplap joints are milled on opposite edges and opposite sides of boards)
(e) Wedgelap w/ Rabbet (from antique corralboard, typically not available in NatureAged or WeatheredBlend; common face width: 7" (typical actual coverage of 6 3/4"); generally cut from 2" lumber to 1 1/4"+/- on thick side and 1/4"+/- on thin side, with rabbet then added; mixed grays and browns (to allow both sides of 2" lumber to be used; back side would often be pressure-washed to soften (but not eliminate) striping that is typical of back side corralboard))
(f) T&G (common face widths: 3", 5", 7", mixed; target thickness often 3/4"+/- NatureAged and 11/16"+/- Antique and WeatheredBlend; fit of barnwood siding T&G often not quite as good as flooring T&G)
Unmilled siding products (a, b, and c) are standard barnwood lumber. Targeted thicknesses and widths of milled siding products (d, e, and f) are generally driven by barnwood lumber inventory on hand. The milling process generally reduces but does not eliminate variation in actual thicknesses and widths (across boards and even within specific boards.) The milling process often creates additional character like loose or fallen out knots. Such defects are generally left in the boards; buyer can decide whether to install them as is, cut them out, or fill them. Kiln drying lumber prior to milling it can increase the tendency for knots to become loose during the milling process. The average length of siding boards (especially milled siding boards) will generally be less (sometimes significantly less) than the average length of lumber boards. Siding square foot prices will generally be somewhat to significantly higher than lumber board foot prices because they reflect more material and, in the case of milled products, additional processing costs.
Trestlewood makes no representations about the fitness of its products for use as siding or in any other application. It is ultimately the Buyer's responsibility to (a) determine which products (and their accompanying characteristics) are acceptable for use on its project and then to (b) make sure these products are handled and installed correctly. While Trestlewood is not a construction or installation expert, it does periodically pass on (without any guarantee of accuracy) information/resources to its customers that it thinks might provide helpful starting points to consider - see, for example, Trestlewood's 6/2/2016 blog post "Thoughts to Consider Prior to Wood Siding Installation" and other blog posts/resources on www.trestlewood.com.
|Processing Options||Additional processing options often available include kiln drying, fumigation, thickness planing/resawing (to reduce thickness variation), edging (to reduce width variation), pressure washing, and metal removal / metal detecting (does not result in guarantee that all metal is removed.)|
|Other||Barnwood is a rustic product with rustic character. Such character can include checking, metal/holes, loose or missing knots, dimensional variation, wane, punkiness/surface rot, gouging, twisting, cupping, color and texture variation, and other imperfections. Barnwood can be very brittle and may split easily. Special care, such as pre-drilling holes for nails, is advisable.|